precote® 30

precote® 30 – Medium Strength Threadlocking Coating with Heavy-Duty Performance

precote® 30 is a medium strength thread locking and sealing coating designed to be used
on all types of external or internal threaded fasteners. It is especially recommended for
fasteners with thread sizes equal or larger than M16 in order to provide easier disassembly.
It’s low Coefficient of Friction provides lower installation torque values and it is ideal
for engine plug sealing applications.

Pre-applied, dry to the touch and providing unmatched vibration resistance for threaded fasteners with sizes M16 and above, precote® 30's signature yellow locking and sealing fastener threadlocking system, provides unparalleled reliability for fastening components in place during assembly. It is activated when compression or shear stress ruptures the micro-capsules after the assembly of the screw. The threadlocking is released and within a short time the system hardens, providing silverback strength and hold – even under the most extreme conditions.

 

Also available with two additives:

  1. “- 3” , precote® 30-3 provides a fast curing time, accelerating the locking effectiveness.
  2. “- 8”, and precote® 30-8 is added for utilization with thread sizes M6 and smaller.

The following combinations are available:

  • precote® 30:
    Standard thread locker for threads > M6 or pitches > 1mm.
  • precote® 30-3:
    Accelerated curing for threads > M6 or pitches > 1mm. Yellow UV marker visible under UV light.
  • precote® 30-8:
    Standard thread locker for threads ≤ M6 or pitches ≤ 1mm. White UV marker visible under UV light.
  • precote® 30-3-8:
    Accelerated curing for threads ≤ M6 or pitches ≤ 1mm. White UV marker visible under UV light.
Application

precote® 30 is a middle strength thread locking and sealing coating designed to be used on all types of external or internal threaded fasteners. It is recommended for fasteners with thread sizes equal or larger than M16 to provide easier disassembly. From screws to studs to pipe threads and non-standardized parts, its dual microencapsulation maintains high integrity and is proven to increase productivity at the assembly line.

 

Features and Characteristics

precote® 30 – Features and Characteristics
Medium strength.
Heavy-duty performance.

  • Only fastener threadlocking coating with dual micro-encapsulation for longer-lasting performance and chemical bonding
  • Dual micro-encapsulation helps maintain the integrity of chemical components
  • Maintains locking and sealing properties when exposed to temperatures up to 200°C
  • High breakaway torque even after repetitive exposures to high and low temperatures
  • Complies and exceeds IFI 125 and 525, DIN 267 Part 27 and major worldwide automotive company specifications
  • Seals against pressures up to 250 bar (3600 PSI)
  • No additional locking devices are required
  • Fasteners with pre-applied precote® 30, are ready for assembly
  • Increases productivity at assembly lines
  • Precise thread coverage every time
  • Can be applied on external or internal threaded fasteners
  • 4 years of shelf life under proper storage conditions
  • precote® 30 is not affected by high humidity conditions
  • Dry-to-touch, non-tacky finish
  • Non-toxic, physiologically harmless and assembler friendly
  • Temperature range: -58°F to 300°F or -50°C to 150°C
Technical Specifications
Color yellow
Thread friction 0.10 - 0.15
Curing time* at RT precote® 30: 6h
to exceed the values precote® 30-8: 6h
according to DIN 267-27 precote® 30-3: 0,5h
Prevailing-in torque PIT on assembly* < 1.0 Nm
Strength without preload BAT* > 10 Nm
Strength with preload BLT* > 1.1 x MA
Prevailing-out torque POT according to DIN 267-27 < 55 Nm
Temperature range according to DIN 267-27 -60°C to +150°C
-75°F to +300°F
Good chemical resistance: meets or exceeds the relevant automotive specifications and DIN 267-27  
Shelf-life 4 years at max.30°C and max. 65% relative humidity  
For storage and transport conditions please see precote® USA  
*All values apply to screws M10 ISO 4017-8.8 plain finish and nuts M10 ISO 4032-10 plain finish, all other thread sizes comply with DIN 267-27. All other surfaces have also to be tested according to DIN 267-27 Annex A.  

MSDS

Product PDF

Releases
GM GM-6175M
GMW14657
Ford WX201
WSSM18P12-A
Caterpillar 1 E-2486
National NCB A 2958
Burman & Sons QC/1007
Perkins Diesel PMS 1.02
VW/Audi DIN 267 P27
BMW DIN 267 P27
Jaguar Land Rover RES.22.FP.01
Daimler DBL 8830. 10
Fiat DT-M-SFA-SSM
PSA B141 235 E
Renault 39.02.010. CATEGORY 1 E

© 2023 Precote® USA|Privacy Policy|Terms & Conditions